Yamaha outboard throttle control adjustment

Outboard mounting height height of outboard transom brackets from bottom of boat transom. An outboard motor shifter and throttle control is the unit that controls the amount of throttle or speed of the outboard motor.

He was not optimistic that much improvement could be made though based on the type of controls that came on the boat.

Yamaha outboard throttle control adjustment. Maybe this will help you better than the other instructionsLay on your back on the deck of your boat underneath your throttle controlLook up at the bottom of your controlYou will see a rubber plugPull that looseYou will see a screw. For lever tension adjustment. 1Remove the four screws that hold the 704 cover in place and remove cover.

2The throttle friction screw is located at the rear of the control box - turn the screw cw to make throttle stiffer and ccw to make softer. Push the throttle to the Full forward position. Ensure that the throttle arm at the motor travels to the throttle stops.

Move the cable to a lower hole on the control if the lever travel is insufficient to reach full throttle. Tighten the jam-nut on the throttle cable with the wrenches. I think this is a simple adjustment fix but wanted to see if anybody else have ever dealt with a Yamaha outboard tiller handle throttle only twisting about 34 of an inch of travel from min to max.

I included a picture to explain what im talking about the red lines indicate the twist travel of the throttle handle. It has a thumb-operated trimtilt switch comfortably on the handle easily accessible neutral warm-up controls and externally adjustable throttle friction. Its now compatible with our V6 42-liter 300 250 and 225 in addition to a range of lower horsepowers.

When you remove the carburetor from your Yamaha outboard motor or if the remote shift lever hesitates when you move the motor into or out of gear you probably need to adjust the shift cable. Usually you have to take slack out of the cable but whether theres too much slack or the cable seems short the procedure for making the adjustment is the same. When activated the outboards will automatically trim up or down at a given RPM.

Maintain throttle setting at the touch of a button. Speed Control can set RPM throughout the range of the engine. Helm Master is second-station compatible and can operate in twin and triple applications.

Available in a stylish chrome finish our 704 Single-Engine Binnacle control now features a more contemporary design and a shorter binnacle length for improved ergonomics and shift feel. It has a thumb-operated trimtilt switch comfortably on the handle easily accessible neutral warm-up controls and externally adjustable throttle friction. Yamaha Outboard Throttle Cable Adjustment.

This prevents the engine from starting in gear. Outboard control cable adjustment for shifting gears forward reverse This video shows how the shifter cable coming from an Evinrude Johnson OMC controller actually changes gears. Adjust the throttle itself.

Start the engine and with the engine running twist the throttle grip. Twist it counterclockwise from the Idle position to increase speed and clockwise to decrease speed. If theres a throttle lever rather than a throttle grip on the tiller move the lever in increments to increase or decrease throttle.

Throttle Friction Adjustment allows you to customise the amount of pressure required to move the throttle handle. Suitable for F150XCA F175XCA F200XCA F225 F250 F300 XTO425 outboards. Concealed Side Mount Control.

An outboard motor shifter and throttle control is the unit that controls the amount of throttle or speed of the outboard motor. The throttle control is a lever that can be pressed forward to increase the speed of the boat. When the throttle level is pushed forward it opens the engine throttle in the outboard which means that more air and fuel.

Yamaha 704 throttle friction adjustment. Remove the top cover of your control. 4 black screws and remove the top cover.

Once the cover is removed. There are two screws on the bottom side of the control. Turn the screws in till they get tight and go one turn more.

Most of thoses screws are loose from the factory. How to replace Yamaha outboard throttle cable Shift cable replacement aka control cables - YouTube. The 704 Premium Control Boxes boast a sleek rounded look thats more than just aesthetically pleasing.

This Yamaha remote control provides you with effortless one-handed operation of the throttle and shift of your outboard. The intuitive design consists of a thumb-operated engine trimtilt switch on the handle. Move the control handle to FORWARD throttle range.

Control handle should move freely. Adjust control handle friction adjustment to prevent vibration from changing throttle setting. Use a flat head screwdriver to adjust control handle friction adjustment screw.

This adjustment is used to increase or reduce the force required to move the control handle. New Yamaha F115 throttle control issue Thanks for the suggestion. As it happens we talked to the local Yamaha dealer yesterday.

There MAY be some adjustment that can be made at the controls end. He was not optimistic that much improvement could be made though based on the type of controls that came on the boat. I have a 2005 115 hp Yamaha outboard F115TLRD and I am trying to figure out how to adjust the throttle resistance to put more friction on the throttle.

When I accelerate and let go of the throttle – it comes back down to idle – very annoying. I have read that you remove the cover see 2nd photo and adjust the screw at the bottom of the area. I ve read from other forum postings to not adjust the throttle body adjustment screws.

Theres two adjustment screws on the binnacle for tension adjustment but Im assuming thats for holding pressure for the shifter lever. The levers tension is not an issue so I have not messed with those adjustments. My binnacle is a Yamaha 704 single lever.

Mounting height dimension for dual outboard installa-tion. Outboard mounting height height of outboard transom brackets from bottom of boat transom. For heights over 22 in.

560mm a propeller that is designed for surfac-ing operation is usually preferred. The outboard should be mounted high enough on the transom so that the exhaust. Outboard must be fastened to boat transom one of two ways.

Permanently fas-tened to transom with thumb screws and mounting bolts provided or 2. Secured to the transom using the optional outboard mounting kit shown below. Should the outboard strike an underwater object or be steered into a sharp turn failure to fas-.

This video shows how the shifter cable coming from an Evinrude Johnson OMC controller actually changes gears. The gear shifting is a bit different then t. The Yamaha mechanical XB outboards use an older technology utilizing physical throttle control cables and are somewhat less expensive than the digital models.

The newer digital XCA motors are fly-by-wire where throttle settings are transmitted over the Command Link Plus network to the engines no control cables or linkages are required. Yeah another damned question. My throttle adjustment on my 704 binnacle aint right.

After having hooked-up both the throttle and gear shift cables I noticed that no matter how much I seem to adjust the gear shift cable that the controls are S T I F F. I loosened up the friction control screw the whole way but this still did nothing.