Yamaha outboard throttle cable adjustment

Ive only had the motor for a couple of days and I am new to outboards. Install shift cable on shift lever pin and install retainer clip.

You may have to by hand spin the prop till he marks line up.

Yamaha outboard throttle cable adjustment. Ensure that the throttle position does not change at the motor. Push the throttle to the Full forward position. Ensure that the throttle arm at the motor travels to the throttle stops.

Move the cable to a lower hole on the control if the lever travel is insufficient to reach full throttle. Throttle Cable Replacement Instructions Crowley Marine May 6th 2018 - APPLICATION Use this instruction sheet when replacing the throttle cable on tiller handle equipped Evinrude E TEC 40 115 HP model outboards SAFETY INFORMATION DOWNLOAD Yamaha Outboard Online Service Repair Manual PDF May 1st 2018 - DOWNLOAD Mercury and Mariner outboard online. You may have to by hand spin the prop till he marks line up.

If the shifter cable does not drop EASILY on the pins the cable needs to be adjusted in or out until it does. If theres still a bunch of play in the cable you can move it in and out theres an issue-worn cable. Throttle link InspectionAdjustment Throttle cable InspectionAdjustment Shift cable InspectionAdjustment Start-in-gear projection InspectionAdjustment Idle speed InspectionAdjustment Under Yamahas Maintenance Interval Chart this should be done every 1006 and 20012 hoursmonths depending on the specific InspectionAdjustment above.

How to replace Yamaha outboard throttle cable Shift cable replacement aka control cables - YouTube. I think this is a simple adjustment fix but wanted to see if anybody else have ever dealt with a Yamaha outboard tiller handle throttle only twisting about 34 of an inch of travel from min to max. I included a picture to explain what im talking about the red lines indicate the twist travel of the throttle handle.

When you remove the carburetor from your Yamaha outboard motor or if the remote shift lever hesitates when you move the motor into or out of gear you probably need to adjust the shift cable. Usually you have to take slack out of the cable but whether theres too much slack or the cable seems short the procedure for making the adjustment is the same. Outboard control cable adjustment for shifting gears - forward reverse - YouTube.

Outboard control cable adjustment for shifting gears - forward reverse. Place throttle cable in position. Use Ball Socket Installer tool PN 0342225 to snap throttle cable connector onto throttle lever.

Place throttle cable in upper anchor pocket. Install cable retainer on anchor block. Hold twist grip in full SLOW position.

Pull firmly on cable to remove backlash. Adjust cable anchor so throttle cam is against idle stop when throttle cable anchor aligns with mounting hole in throttle. Shift Cable Adjustment.

Pull firmly on shift cable casing to remove backlash. With outboard and tiller handle shift lever in NEUTRAL place the cable trunnion into the lower anchor pocket. Adjust the trunnion nut so the casing fits onto the shift lever pin.

Install shift cable on shift lever pin and install retainer clip. Align the shift cable end guide with the center point made in Step 2. Place shift cable on anchor pin.

Adjust cable barrel so it slips freely into the barrel holder. Secure shift cable to the anchor pin with hair pin retainer. N a b c d e f a-Center Mark b-Anchor Pin c-Barrel Insert d-Cable Barrel e-Barrel Holder f-Hair Pin Retainer 7.

Adjust the throttle itself. Start the engine and with the engine running twist the throttle grip. Twist it counterclockwise from the Idle position to increase speed and clockwise to decrease speed.

If theres a throttle lever rather than a throttle grip on the tiller move the lever in increments to increase or decrease throttle. Shift and throttle Linkage - complete adjustment procedure Yes Justinde I think once and for all we should have this documented clearly with pictures. Im not sure though how much picture we can post in this website.

So I hope someone will post 1. Carburetor and Autolube Cable Adjustments. Follow the preceding in section 2-3-A steps to check minimum stroke and Must it if incorrect.

Then adjust the carburetor and pump as described in the steps below. 1 Throttle Cable Adjustment. Adjust the carburetor with the engine at idle and remove all but 1 mm of slack from throttle cable B.

Ive only had the motor for a couple of days and I am new to outboards. Joined Sep 22 2003 Messages 28571. Jul 2 2006 2 Re.

Throttle Cable Adjustment Here are a couple things to check. Put the control lever in neutral. Now disconnect the throttle cable at the engine.

While pulling on the cable end to remove slack. 90-10184020 FEBRUARY 2001 Printed in USA. - 2001 Mercury Marine Page 1 of 26 INSTALLATION MANUAL 25 30 40 50 and 60 HP 4-Stroke NOTICE TO INSTALLER.

After completing assembly these instructions should be. Yamaha Outboards Topics by Horsepower.