22
Feb
Press a section of the widest end of the bearing into the outer edge of the grease pile closet to the thumb forcing grease into the interior of the bearing. How to Replace Trailer Wheel Bearings - YouTube.
Before any synchronization adjustments are made your trailer brakes should be burnished-in by applying the brakes 0-30 times with approximately a 0 mph.
Trailer wheel bearing replacement instructions. Take 1 wheel off the trailer to access the hub assembly. Loosen the nuts on all wheels with a lug wrench while the trailer is on the ground. Jack the trailer up just enough to lift the wheels off the ground.
Finish unscrewing the nuts on 1 wheel with the lug wrench remove them and slide the wheel off the hub. How to Replace Trailer Wheel Bearings - YouTube. Trailer Wheel Bearing Inspection Maintenance and Replacement 1.
Wheel End Disassembly A. Follow the manufacturers recommended procedure to remove the tire and wheel assembly hub cap cotter pin adjusting nut and washer. Pull the hub assembly toward you to loosen the outer bearing cone assembly.
Remove the outer bearing cone assembly. Push the wheel assembly in and out while oscillating it to seat the bearings. Read the bearing end play as the total indicator movement.
If end play is. To pre-load the bearings install the spindle washer and spindle nut onto the spindle with the hub and bearings in place. Tighten the spindle nut finger tight until snug and then with channel-lock pliers or a crescent wrench tighten the spindle nut another 14 turn or about 15 to 20 ft pounds of torque.
Now turn the hub ten revolutions. The bearing cup use the proper tool to drive the new cup into the hub ig. Coat the hub cavity with the same wheel bearing grease to the depth of the bearing cups smallest diameter.
Apply a light coat of grease to the spindle. Place the inner bearing in the hub. Lightly coat the lip of the new SKF seal with the same wheel bearing grease.
We can accomplish this in three different ways. 1 Measure the old Bearings. After removing the bearings measure the inside diameter of the bearings with your calipers.
The most common sizes with UFP are the following. 106 1-116 138 1-38 125 1-14 and 175 1-34. 2 Measure the spindle itself.
This video is of me checking and repacking the wheel bearings on my utility trailer. Replacing your Boat Trailer Bearings Step by Step Instructions - YouTube. Replacing your Boat Trailer Bearings Step by Step Instructions Watch later.
This video shows how to change the wheel bearings on a boat trailer. This includes removing the wheel the brakes and then the original races. We then go thr.
When installing trailer bearings or replacing them you need a pair of pliers a lug wrench a hammer a flathead screwdriver and the necessary means to jack the wheel up safely. Be sure to loosen the lug nuts with the lug wrench first. Once the wheel is in the air all you have to do is follow a few simple steps.
Along with bearing adjustment proper lubrication is essential to the current function and reliability of your trailer axle. Bearing should be lubricated every 12 months or 12000 miles. Repack bearings as follows.
Place a quantity of grease into the palm of your hand. Press a section of the widest end of the bearing into the outer edge of the grease pile closet to the thumb forcing grease into the interior of the bearing. Before any synchronization adjustments are made your trailer brakes should be burnished-in by applying the brakes 0-30 times with approximately a 0 mph.
Decrease in speed eg. Allow ample time for brakes to cool between application. After replacing shoes and linings your trailer brakes should be burnished-in by applying the brakes 20-30.
Times with a 20 mph. Decrease in speed eg. Allow ample time for brakes to cool between application.
This allows the brake shoes and magnets to begin seating to the brake drum. W ith your new or still-good trailer wheel bearings clean and packed reassemble your bearing sets in your hubs set your bearings and torque your lugs to your trailers proper specifications. Make sure your dust caps or bearing protectors are properly on as well.
Wheel Bearing Replacement 1. Wheel End Disassembly Follow the vehicle manufacturers recommended procedure to remove the tire and wheel assembly disk brake caliper dust cap cotter pin adjusting nut and washers. Pull the rotorhub assembly toward you to loosen the outer bearing cone assembly.
Remove the outer bearing cone assembly. With the wheel hub and hub seal removed as described above remove the wheel bearing cups using the following procedure. Drive each wheel bearing cup out with a long brass drift placed through the hub centre against the inner face of the respective cup.
The drift should be placed in alternate positions around the cup to. The wheel bearings and cause failure. Bearing Inspection Wash all grease and oil from the bearing cone using a suitable solvent.
Dry the bearing with a clean lint-free cloth and inspect each roller completely. If any pitting spalling or corrosion is present then the bearing must be replaced. The bearing cup inside the hub must be inspected.