Trailer hitch loose on ball

My hitch is loose in the receiver and rattles. This collar is secured by a safety pin.

Place the lock washer and the nut onto the bottom of the shaft and then move them up all the way so that they touch the ball mount.

Trailer hitch loose on ball. If your hitch ball is loose then you will want to check to see if there is a ft-lb torque rating located on it. For instance the Tow Ready 2 Hitch Ball 63845 has a torque rating on the nut for 250 ft-lbs. If you cannot find a torque rating then the next best thing would be to torque it down so that the washer is flat.

I have a couple different options on ways to fix a loose ball mount. The Anti-Rattle Hitch Pin SHP2061 dramatically reduces any movement or vibration between your hitch and hollow shank ball mount. The No-Rattle Trailer Hitch Wedge MPG908 will take up play and eliminate rattle.

This is a factory provided piece from Toyota for my Highlander. On a long tow the ball nut could have come completely off. There is a lock washer so I am surprised that it loosened.

I never had this happen before. Just a reminder to check the nut under your hitch ball before towing. Posted 08-15-2008 0144 PM ET US.

With a 61 261 848 head Rochester Monojet carb SM420 4-speed 410 rear dual reservoir MC Bendix up front 23585R16 tires 12-volt walternator electric wipers and a modern radio in the glove box. Copy Link to Clipboard. Trailer HItch Ball Came Loose.

The required ball size for the coupler should be stamped into the metal on the top of the coupler. If you were using a 1-78 trailer ball with a coupler designed for a 2 inch ball it would explain why the ball is loose in the coupler. If this is the case DO NOT tow the trailer until you can get the correct size trailer ball.

This should be near the front end of the receiver. Then get a 12 bolt and lock washer and nut all grade 8s and put the nut and lock washer on the bolt in the middle of the innermost ball mount and tighten down. You will be bolting the inner ball mount the sleeve and the hitch together.

This will stop ALL MOVEMENT of the ball mount. Rapid Hitch Adjustable Aluminum Ball Mount Kit w 2 Zinc Balls - 5-12 Drop. Trailer Hitch Ball Mount.

Reese has a series of hitch bars where there is a hex recess that the hex flange on the their hitch ball sets in. This way the ball cant rotate. They have them at Walmart.

You might also check to make sure that you dont have the hitch adjusted too tight. If its too tight then the trailer will try to rotate the ball whenever you turn. Ball loose on hitch Several other ways to stop it loosening by itself.

Use locktite on the threads. Get an old sharp screwdriver and deform the thread up tight to the nut on the free side after tightening using a hammer on the screwdriver. Use a second nut tight up against the first as a locknut.

This type of coupler has a collar that would slide up securing the jaws of the coupler in place over the trailer ball. This collar is secured by a safety pin. If the pin is missing this could explain why the coupler is coming open.

If you have a standard latch-type coupler it. One of the biggest concerns opponents of trailer hitch grease have is that it can attract dirt. However if you use a dry graphite lubricant it will keep dirt away while still maintaining your trailer hitch ball.

Additionally when you apply grease you should make. First insert the shaft into the receiver hole so the trailer ball is facing upward. Place the lock washer and the nut onto the bottom of the shaft and then move them up all the way so that they touch the ball mount.

Use another wrench to tighten the nut on the bottom until its locked in place. Hitch ball squeaks happen when the thin metal on the ball on the tow vehicles hitch wears away. This is due to the regular motion and turning of the trailer coupler the part that goes over the ball over the hitch ball.

Over time and without lubrication the ball will wear out as will the ball socket on the trailer coupler. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. I never can see myself removing this ball from the hitch.

It is a WD hitch and has the 2 516 ball on it. Again the ball is tight just not AS tight as I would really like it. 34 drive ratchet and a pipe wrench to back up the ball.

There is a lot of steel on both the hitch AND the ball. Climb under the hitch and look up in there. You should see a nut or bolt through the latch.

Find a socket to fit and loosen that up one round then sit it back down on ball. May take a couple of times to get it right. But that should take care of it just make.

It happens when the hitch on the trailer doesnt release the ball. Chock the trailer wheels so it wont roll forward. Start the engine in the TV and put the transmission in Drive.

The TV will move forward 14. Set the Parking brake on the TV. Now the hitch on the trailer will release from the ball.

Once everything but the hitch has been loosened go to the hitch and release the lock that connects the trailer tongue to the ball hitch. If there are any safety locks or. That its a natural reaction to maintain the parts of your vehicle in working order and that the alternative to greasing is to slowly watch your once-shiny trailer hitch ball get more bitty and gritty and eventually to watch it succumb to rust year on year until eventually you dont trust it and have to get it replaced.

I want to change the position of the ball in my receivers tongue. I bought a big honking 1-12 impact socket. It was 34 drive and so I needed an adaptor for my 12 drive air impact wrench.

At 110 lbs air I cant get the nut to budge. How do you get the silly ball to unbolt. A trailer coupler is a mechanical device that connects a trailer to the hitch of the tow vehicle.

Trailer couplers come in several different configurations but all work by clamping around the hitch ball. The means to do this varies somewhat. Some couplers employing a hand wheel to tighten the clamp to the ball.

Another common arrangement is a lever or toggle to lock the coupler. There are a number of hitch adjustments that work together to spread the tongue weight of the trailer to all axles. Dallas WBCCIVAC 8481 puts it this way.

Adjust the hitch ball height to level the trailer. Adjust the weight distributing bars to level the tow vehicle. Adjust the hitch head angle to level the bars.

07 TRD Off-Road Auto. I have a 2007 Tacoma TRD with FACTORY receiver and tow package. I have a reese hitch with 2 ball.

My hitch is loose in the receiver and rattles. It rattle alot when going over bumps and even more so on an empty trailer. The fit of the recier and the insert with ball is pretty poor so I tried 3 other.