17
May
Measure and cut off excess threads. 4 Drill a 1⅞ hole higher than the pump outlet and install the Directional Discharge provided.
Leave enough length to attach strainer.
Thru hull livewell pump installation. Level thru-hull fittings must have a seacock shut-off valve. Mount ¾ NPT-M pump inlet port directly to seacock. For extended inlet ports cut to desired length to fit.
PLUMBING Use smooth ID. Discharge tubing or hose. Tubing hose should be rated for below water line use.
Always use double clamps for connections below the water line. Tubing should enter tank at top to avoid. Step By Step Installation.
Locate the spot to drill a hole. Locating an appropriate spot where you drill a hole is very vital before installing the live well pump. To ensure that you dont go wrong make sure the spot location is below the waterline when the boat is not moving.
SHURFLO BAIT LIVEWELL PUMP INSTALLATION OPERATION MANUAL MOUNTING Mount scoop-type thru-hull high speed pick-up to hull. Do not drive screws through hull. Below water level thru-hull fittings must have a seacock shut-off valve.
Mount ¾ NPT-M pump inlet port directly to seacock. For extended inlet ports cut to desired length to fit. Go to Blackburn Marine and check out all the brass configurations you can think of.
Then make it fit to your pump. Put a marelon seacock valve between thru hull and pump. Overflows directly out the top side of the Livewell or Bait Well Tank.
This Livewell or Bait Well setup is easy to install. As you can see by the diagram the overflow outlets directly through the hull of the boat above the water line allowing you to refresh and recirculate the water in your livewell or bait well tank. Pump must be tilted at a 45 angle on completed installation so all air can escape upwards.
Drill a 1 116 hole for the pump base. Measure and cut off excess threads. Leave enough length to attach strainer.
Insert pump and tighten. 4 Drill a 1⅞ hole higher than the pump outlet and install the Directional Discharge provided. Control the Flow.
As you pump water into a circulating livewell old water exits from a screen drain near the top. To avoid an overflow the drain hose needs to be about twice the diameter of the inbound hose. So if you have a 1-inch-inside-diameter feed hose for example you need a 2-inch-ID drain hose.
Install either the KA700RK or KA110RK. This will allow fish to remain healthy while the standard livewell pump is off when the boat is in contaminated water or when the pump is air-locked. Many boats have the livewell pump installed on the transom.
When the boat is on a plane the intake of the pump is out of the water and is ineffective. The boat can also be. Livewell Pump Replacement - Aluminum Boat Project 30 - YouTube.
Livewell Pump Replacement - Aluminum Boat Project 30. Fills your livewell with clean oxygenated water to keep your catch healthy. The internal anti-airlock fins ensure even flow of water to your livewell.
The cartridge is easy to remove for cleaning or replacement. Pump is fully submersible and utilizes tin-coated 16-gauge wire for safety. Drill a 1Ó diameter hole through the transom or hull bottom.
If drilling through the transom make sure the hole inside the boat is beneath the w aterline o utsid e the b o at when the boat is standing still. Install a thru-hull pickup tube with a filter grate to prevent. The patented infuser technology introduces air into the base of the Livewell pump through the air control centre producing millions of micro-fine bubbles.
Because the bubbles are so small they remain suspended in the water longer providing more aeration to your delicate bait and catch. Designed to fit almost any custom tank. Shoreline Marine Livewell Pump Fishing Equipment 80.
Seachoice 19441 Bilge Pump Installation Kit for 34. T-H Marine Push In Overflow Drain Tube Straight fits. T-H Marine Aerator Filter Dome 1 Hole ID fits 34.
Sea-Dog 520750-1 Polypropylene Thru-Hull - 34 Hose. T-H Marine Push In Overflow Drain Tube 90 Degree fit.