Replace rigid toilet supply line

Whenever I replace a sink I replace the sink the fixture both supply lines and the supply valves as well as all of the drainage components to the wall. The supply line to a toilet can become corroded or blocked requiring replacement.

Obtain a flexible toilet water supply line that is close to the length you need.

Replace rigid toilet supply line. Replace the supply lines to your toilet with advice from a professional pl. The supply line to a toilet can become corroded or blocked requiring replacement. Turn the valve back on to allow water to run to the toilet tank.

Operate the toilet and check for leaks. How to Replace a Rigid Toilet Supply Line. There is likely no good reason for you to have a rigid supply line so our recommendation is to just replace it with a flexible toilet supply line.

You should be able to simply loosen the nuts on each end of the rigid supply line and remove it with ease. Save on Repairs with. That connection will be on the underside of the tank and you may need another towel handy as some water may still drip out of the old supply line.

Install the new supply line by hand tightening the white plastic nut to the toilets fill valve nipple on the under side of the tank. Then hand tighten the metal nut to the supply valve. The rubber washer and coupling nut 42397 is included with your toilet tank.

Slide the coupling nut onto the rigid supply line. Connect the rigid supply line to the supply stop. Slide the coupling nut to the top of the rigid supply line.

Press the rubber washer into the coupling nut. Handtighten the coupling nut to the fill valve shank. Then loosen the nut to the chrome supply pipe at the toilet fill valve on the bottom then the nut holding the fill valve into the toilet.

Once youve done that you can lift out the toilet fill valve then will have all the room you need to lift the chrome supply line out of the existing valve. Then you can replace any parts you want. The issues sounds more like a loose toilet tank than a piping issue.

If the tank is loose and you lean back the connector will have to flex in order to keep from leaking. Sure a flex is a better idea for your application. But fixing your real problem is even better.

The solution to all this mess is to replace the angle stop valve with a new quarter turn angle stop valve and a new no burst stainless steel supply line. These valves will shut off even if not turned in a long long time and the flexible stainless supply line can be easily changed if the need be. Cant remove compression nut from supply line.

Goldsmit FL Try as I might I cannot get the compression nut off my supply line to fix a leak on my toilet. The line is rather old 12 years and is the original plumbing. Ive hit it with WD40 and used 2 pliers but its not moving at all.

Im worried I might damage the line if I keep at it. Supply Line - a metal or plastic line that carries water from the Main Line to an individual fixture eg. Faucet toilet etc in the home.

What pipe is best for water supply. Galvanized Piping Galvanized metal is commonly used in construction but pipes made from galvanized steel can be used in plumbing applications. Replacing a Toilet Supply Line.

Replacing the supply line is pretty easy. Shut the water off before you loosen the fittings. Loosen the fittings and remove the old supply line.

See the article on Toilet Supply Line Fittings for information on getting the supply line connected correctly. Obtain a flexible toilet water supply line that is close to the length you need. If you cut them in half first and then unscrew the compression nuts from both ends they will come out very easily.

Then you can measure from the face of the threaded ports on the faucet to the ports on the supply stops and get a flexi supply hose that will leave a comfortable 3 loop in the line between stop and faucet. Take a hacksaw blade wrap a cloth around it and then cut that plastic nut off by cutting into the plastic so you make a line through the entire nut. After you have a good deep cut into the nut you can take a flat screwdriver and set it into the cut and twist it to crack the nut and finally remove the fill valve.

Whenever I replace a sink I replace the sink the fixture both supply lines and the supply valves as well as all of the drainage components to the wall. I also clean out the inevitable build up in the stub out. It is much much easier to install the fixture the new supply.

Locate the supply hose connector under the tank and note whether its made of plastic or metal. If its plastic youll probably be able to unscrew it by hand. Put a bucket under the tank.

Rigid Water Supply Line Leaking This happened recently so again I replaced the red valve seal. Unfortunately this time water from the tank was seeping back into the bowl so I was told to replace the entire flush valve which means removing the tank from the bowl. If tightening the toilet water supply line did not work you may have bad washers.

You need shut the water off at the shut off valve. Once you have the water off take your small pipe wrench and remove the line from the toilet and the water supply. There will a rubber washer in each fitting.

Remove the washers and replace them. Replacing Toilet Supply Lines. Leak issues can arise over time and when they come about you will likely need to replace the line.

This task can be performed by the novice plumber if you just follow these easy steps. Shut off the supply of water to your toilet and in almost all. Replace Bathroom Water Supply Lines Without Leaks.

One of the biggest problems when swapping out water supply lines is knowing how tight the connections should be. Obviously this is important to prevent water leaks. Most directions say to hand.