31
Jul
Also is the threading on a propeller shaft a reverse thread. Each tool size comes with a heat treated extractor bar.
Then you will see a small platewith 3 screws remove themThen you will need a bearingcarriage tool Install it.
Mercury prop shaft removal tool. Dont fight ituse the right tool. Hill Marine now has a new Bravo III Prop Wrench that makes prop removal and install quick and easy. One tool does it allthis wrench fits both prop nuts the 1-716 outside nut and the 2-34 inside nut.
The Hill Marine Bravo III Prop Wrench is made of durable and corrosion resistant stainless steel highly polished. Theres no better prop wrench. 04-24-2012 0315 PM.
I recommend you purchase a service manual for this repair. You want to be sure its done properly. Yes the seals and propeller shaft should be all that is required as long as nothing else was damaged.
Jetski Impeller removal tool shaft holder tool Sea Doo Yamaha Kawasaki Polaris Honda. FZS SHO 09-14 VXRVXS 11-16GP1800 Will also fit most V4V6 Mercury outboard motor shafts. 20mm splined female shaft prop tool.
Shaft Holder Yamaha BOAT XR1800 00. Its a 1992 99 Merc. In order to remove the propeller shaft from the gear case you typically have to remove a circular retainer fitting which threads inside the cone of the lower unit bullet.
This fitting typically has an unusual shape which requires a. Universal 3 Blade Propeller Puller. Bearing Retainer Tool Bravo III 91-805382T.
This kit comes with a pre-drilled buffed stainless steel plate and gasket all necessary hardware instructions and cut out template. A recommended optional tool kit PN 528-1020 is available for easier dis-assembly and re-installation for the swivel shaft. This kit will only work on Bravo 1 Bravo 2 Bravo 3 and Alpha 1 Gen 2.
N36A Mercury Quicksilver 91-17257 Wrench OEM Specialty Marine Tool. VINTAGE MERCURY OUTBOARD PISTON RING COMPRESSOR 13 OF SET OF THREE 91-31461A2. 5 out of 5 stars.
1 1 product ratings - VINTAGE MERCURY OUTBOARD PISTON RING COMPRESSOR 13 OF SET OF THREE 91-31461A2. First you remove the prop. Then you will see a small platewith 3 screws remove themThen you will need a bearingcarriage tool Install it.
Vypart Flywheel Puller Removal Tool Outboard1 91-849154T1 and Lift Ring 91-90455-1 Compatible with Mercury Mariner Compatible withce Yamaha 44 out of 5 stars 13 1799 17. Remove the prop from the engine by bending the retaining tabs that hold the prop nut. Then use a wrench to remove the propeller from the shaft pulling straight out.
Use a hammer and punch to remove the carrier nut. The manual says that a special tool is required to remove the carrier but if the tool is not available it states that you can use the thrust hub as a removal tool by placing it on the prop backwards with the hex end of the thrust hub now exposed and the hex end of the hub will fit a conventional box wrench thereby becoming the removal tool. Outboard Prop Shaft Seal Puller Special Tool Yamaha Mercury Johnson Evinrude FSM070.
This was one of my favorite special tools and for pulling prop shaft seals it cant get any easier with this tool. It will fit Yamaha Mercury Evinrude Johnson Suzuki motors from various HPs from 40HP-400HP all of the seal drivers may not fit perfect but the seal. Drive Shaft Adapter Tool - Mercury Mercruiser Alpha.
Add to Wish List Add to Compare. Drive shaft Puller Plate Bar - Force Merc Bravo I II III. Add to Wish List Add to Compare.
Drive Shaft Retainer Nut Wrench-. Tool Gimbal Bearing Installer Mercruiser OMC Volvo SX. Installation Tool for Gimbal Bearings on Mercruiser OMC and Volvo Penta SX sterndrives.
Replacement Part is Available. Click for More Info. Tool Hinge Pin for Mercruiser 1.
These 3 tools made only by JR Marine are a quick and easy way of removing or replacing tapered shaft bearings. Each tool size comes with a heat treated extractor bar. This bar is 14 long and will fit on all 20 and 40 ton hydraulic presses.
Simply place shaft in extractor bar place in press and remove bearings. Removal of Prop shaft on 99hp Merc So 99 have the tool you need built into the prop hub spacer thake the prop off and if the spacer has a SS washer around the part that slides into the prop remove it and use the hex nut on the back to unscrew the carrier remember its LH thead. If not you may buy one thru a Mercury dealer or if your handy make one.
What size socket do I need to remove the nut holding on my propeller on my 2009 E-TEC 150-HP engine. Is there any trick to this. Is the procedure to just put the E-TEC in gear and loosen the propeller shaft nut.
Also is the threading on a propeller shaft a reverse thread. Thanks Tom W Clark. Posted 12-02-2009 0642 PM ET US.
Position Product Name Price Set Descending Direction. Prop Shaft and Bearing Housing Remover JohnsonEvinrude 25-35hp. Prop Shaft and Bearing Housing Remover Yamaha 30-100hp.
5 Coupler Flange Removal Tool - Marine Transmission Coupler Removal Tool by Buck Algonquin 50MCP00500 WILL REMOVE MOST COUPLERS. IF COUPLER IS REALLY FROZEN ON OR THERE IS A LOT OF RUST IN THE BORE THIS MAY NOT WORK. All couplers must be fit and faced to the propeller shaft to allow for an accurate alignment.
Use a Mercury carrier tool to remove the bearing carrier assembly. The assembly has a reverse thread so turn it clockwise to remove it. Remove the prop shaft and the reverse gear from the bearing carrier assembly and secure the assembly in a vice.
Prop Smith PS225 Tool. PropSmith 225 Propeller Installation and removal tool for 225 shaft For use with 3 hol. PropSmith 225 PH225-PL225.
GLM is proud to introduce our Service Tools for the Marine Industry. 90065 Prop Wrench Kit for 1-116 Prop Nut OEM. 91-8218871 Honda 89-89206-ZW7-000AH For Mercury Mariner.
Force V4 V6 and all Mercruiser. 90066 Prop Wrench Kit for 1516 Prop Nut OEM. 91-856639A1 For Mercury Mariner and Force OB.