05
Nov
If there is a significant amount of force or the tool will not go in all the way but somehow you get it all back together. This Tool is similar to MerCruiser PN 91-805475A1 which used to be PN 91-57797A3.
Yes you align the engine with the front mounts.
Mercruiser alpha one engine alignment. B Attempt to insert solid end of Alignment Tool through gimbal bearing and. Into engine coupler splines. If it will not insert easily proceed to following.
Ccarefully raise or lower the engine as necessaryvia the hoist on the lift tab and. Help with MerCruiser engine alignment It all depends on how much force you need to apply to get the alignment tool and presumably the drive shaft into the coupler. If you are splitting hairs then it may be OK.
If there is a significant amount of force or the tool will not go in all the way but somehow you get it all back together. Yes you align the engine with the front mounts. There are two mounts in the rear as well.
The proper hardware must be installed and the hardware torqued to 35-40 lb. Alpha one Engine Alignment. Jump to Latest Follow 1 - 20 of 22 Posts.
1 of 2 Go to page. Turn the nut on the underside of the motor mount to raise lower or shift the position of the motor as indicated and then recheck the alignment with the alignment tool to see if more adjustments are needed. Once its perfect retighten the top engine mount nuts and reinstall the lower unit.
With the engine dangling from the center lift ring the front of the engine the only place you should make adjustments can be lowered or lifted to make alignment. Most can just eyeball the coupler through the gimbal bearing to get it close enough to insert the tool though a 1 pipe will do in a pinch. Mercruiser Alpha One Alpha One Gen Two Bravo OMC Engine Alignment Tool W Steel Gimbal Bearing Installerchina sellers ones are out of aluminum and dont bolt downFREE UPS SHIPPING IN THE LOWER 48 USA STATES THIS SET INSTALLS THE BEARING STRAIGHT AS THE ALIGNMENT TOOL IS IN THE COUPLER WHEN INSTALLING THE BEARING COMPARED TO.
Gimbal Bearing Alignment and Install Kit fits for Mercuiser Alpha Alpha 1 MR Bravo OMC Cobra and Volvo 1 61 99 Get it as soon as Wed Sep 29 FREE Shipping by Amazon MBS Mfg Compatible for Mercury Mercruiser PN 91-805475A1 OMC Volvo Engine Alignment Tool 156 32 99 Get it as soon as Thu Sep 30 1999 shipping. In 1998 Mercruiser introduced the 201 gear ratio to the Alpha Generation 2 Sterndrives which has since replaced the 1941 SHIFT LEVER One noticeable difference between the Alpha Gen 1 Gen 2 Sterndrives is the shift lever as shown in Figure 2. The MerCruiser stern drives shift cable connects the driver controls to the shift control plate.
A shift interrupter switch connects to the shift plate and stalls the engine when you shift in and out of gear to help prevent damage to the stern drive. This switch is directly centered in the assembly when the cable. Quicksilver Engine Coupler Spline Grease 92-816391A4 Special Tools DESCRIPTION PART NUMBER Alignment Tool Assembly 91-805475A1 Transom Specifications 22170 a e c d a b b f a - Transom Thickness-2-2 14 in.
51-57mm b - Transom Surfaces-Parallel to within 18 in. 32 mm c - Area Covered by Inner Transom Plate - Flat to within 18 in. Mercruiser Alpha one Bravo Engine Alignment Tool W Gimbal Bearing Installer.
Top Rated Seller Top Rated Seller. 1 S p G o n s o 9 r C e d 5 Q F 5 W 7. Mercruiser Alpha Bravo OMC Boat Engine Alignment Tool USA made Fast Shipping.
FAST FREE SHIPPINGNew engine Alignment Tool for Alpha One Pre Alpha Gen 270940004316 MERCRUISER ALPHA BRAVO OMC Boat Engine Alignment Tool USA made Fast Shipping - 5069. Engine Alignment Tool Compatible for Mercruiser Sterndrives including Pre-Alpha R Alpha One MR Generation II all Bravos Volvo SX and OMC Cobra. This Tool is similar to PN 91-805475A1 which used to be PN 91-57797A3.
The length of the bar is approximately 23-58 inch. A higher quality tool than the competition. Prior to summerizing this year a friend and I decided to pull the engine and replace the ring gear on the flywheel.
In doing this we removed the engine cover and removed the lag bolts that go into the stringer so as to not change the adjustable motor mounts. Obviously the other bolts holding the engine in the rear were removed. Mercruiser engines must be properly aligned or the Drive Couplerwill be damaged.
The drive is attached to the engine through the use of a drive coupler. This coupler is bolted to the engines flywheel or crankshaft. The male splined driveshaft yoke from the outdrive slides into the female splines of the drive coupler.
This is a 1984 Ranger 395-V io inboard outboard bass boat. It has a Mercruiser 260Chevy 350 engine. I have been restoring it.
I just replaced the gimba. Gimbal Bearing Alignment and Install Kit Heavy Duty Engine Alignment Tool Set Fits for Mercruiser Alpha Bravo Volvo OMC 46 6499 Marine Tech Tools Mercruiser Gimbal Bearing Alignment and Install Kit 69 8400 Yoursme Gimbal Bearing Alignment and Install Kit fits for Mercuiser Alpha Alpha 1 MR Bravo OMC Cobra and Volvo 18 6499. OEM QuicksilverMercury Alignment Tool Assembly 91-805475A 1.
Please confirm fitment of MerCruiser parts with your serial number Photos and descriptions provided via Mercury may not always be accurate All of our Mercury parts are sold and priced EACH. Mercruiser Alpha One Alpha One Gen Two Bravo OMC Engine Alignment Tool W Gimbal Bearing Installer. FREE UPS SHIPPING IN THE LOWER 48 USA STATES.
THESE OUR MADE HERE IN THE USA IN OUR MACHINE SHOP. THANKS FOR SUPPORTING AN AMERICAN MACHINE SHOP UNLIKE A LOT OF THE OTHER IDENTICAL CHINA ONES BEING SOLD ON HERE. Outdrive Alignment Tool for Mercury Mercruiser OMC Cobra and Volvo SX.
This version comes with a hanging ring for the tool. This tool replaces the following part numbers. MerCruiser - PN 91-805475A1 91-57797A3.
Volvo SX - PN 3851083. OMC Cobra - PN 18-4442. Will work on Pre-Alpha Alpha One Gen 2 R MR All Bravo Volvo SX OMC Cobra Drives.
Gimbal Bearing Installer Puller Remover and Enigne Alignment Tools Set For Mercruiser Sterndrives Pre-AlphaR Alpha OneMR Generation II all Bravo models for Volvo for Omc 50 out of 5 stars 1 MTC 5001791-805475A1 Engine Drive Alignment Bar. This is a set of Four 4 Tools. Engine Alignment Bar Tool Compatible for MerCruiser Sterndrives including.
Pre-Alpha R Alpha One MR Generation II all Bravo models. This Tool is similar to MerCruiser PN 91-805475A1 which used to be PN 91-57797A3. Volvo SX PN 3851083 and OMC Cobra PN 18-4442.